EMIS_Logo






Pedalboard

Kits

Synth

Kit

MIDI Converter

Kits

MIDI Controller

Kits

Accessories

Doepfer Logo

:               OEM  Kits               :     

Doepfer Pedalboard Kits

Doepfer MBP25


The MBP25 is a Midi bass pedal controller, designed for the Fatar PD/3 (13 note) pedal board, of which two can be used to form a 25 note pedalboard.
A controller potentiometer for loudness/volume control (Midi CC#7) is also supported.
There are 6 momentary buttons (with LED's) and a 3-digit LED display. The 6 switches control parameters: Midi channel  (1 - 16), Transpose,  Program change,  Operating Mode (Note, Program Change, Realtime Messages), Up (inc) and Down (dec).
The MBP25 has a non-volatile memory for  all settings, and is equipped with Midi In and Midi Out.

The data appearing at the Midi in is merged with the data generated by the MBP25,

allowing other devices to be merged.
The MBP25 is a fully assembled and tested board with dimensions 73x 82 x 25 mm.

An external power supply (7-12VDC@min. 250mA) is optionally available.

£65

Doepfer MBP13 Fatar PD3

Doepfer Synth Kit

Doepfer DIY Synth Kit  (Temperature compensated version)

£99

VCO: Saw & Square output (variable pulse width). 4 frequency CV inputs (1V/octave). Frequency CV summing input (for additional CV inputs) Two PW/PWM CV inputs PW CV summing input (to increase the number of CV inputs if more than two PW CV inputs are required) Linear FM input Hard sync input
VCF: Multimode filter lowpass, highpass and bandpass output (optional low-notch-highpass) 12dB/oct Two frequency CV inputs (one roughly 1V/octave, one roughly 0.5V/octave) Frequency CV summing input (for additional CV inputs) Audio input Audio summing input (for additional audio inputs) Overdrive/distortion possible.  Manual resonance control with Resonance up to self oscillation
VCA: Exponential control scale One CV input CV summing input (for additional CV inputs) Two audio inputs Audio summing input (for additional audio inputs).   Overdrive/distortion possible.
ADSR: for attack, decay, sustain and release controls. 3-Way Range switch.  LED display. Gate Input,  ADSR output
LFO: frequency control and 3-way  range switch. LED display.  Triangle and rectangle outputs
Slew Limiter,  Inverter Input Summing input (can be used to increase the number of inputs).


Doepfer DIY Synth Doepfer DIY Synth

Doepfer MIDI Converter Kits

Doepfer CTM64


The CTM64 is a universal MIDI out kit. Up to 64 free contacts can be connected to generate MIDI note on/off or program change messages. Up to 4 pots can be connected to generate common MIDI controllers, pitch bend and aftertouch. Additionally a 1/4" jack socket is available for connecting a sustain pedal. . In the note mode , closing of a contact generates the corresponding MIDI note on messsage, opening generates note off - both without velocity (velocity is fixed at 100). In the program change mode, closing of a contact leads to the corresponding MIDI program change message.  The incoming MIDI messages are merged to the data generated by the CTM64. (several CTM64's can be linked together).
The CTM64 is not supplied with a power supply, as power is likely to be sourced from the equipment being interfaced. An optional PSU is available


Doepfer CTM64

£89

CTM64 Cable set



The CTM64 connecting cable set consists of 4 IDC cables fitted one end (50cm long)
Longer cables can be made to order.

£19

IDC Cable Set

Doepfer MTC64


The MTC64 is a universal MIDI in Kit. Up to 64 MIDI note on/off or program change messages can be converted into 64 TTL voltages (0/+5V). In note on/off mode (without velocity) incoming MIDI note on/off messages control the 64 outputs provided that the MIDI channel and note range correspond to the settings of the MTC64. A note on message will set the corresponding TTL output to a high level (+5V), the note off message will reset the output to a low level (0V). (This action can be reversed)

 In program change mode, MIDI program change messages are used to control the 64 outputs. In this mode only one of the 64 outputs is activated. The number of the activated output is identical to the program change number received.
The MTC64 is not supplied with a power supply, as power is likely to be sourced from the equipment being interfaced. An optional PSU is available.


Doepfer MTC64

MTC64 Cable set



The MTC64 connecting cable set consists of 4 IDC cables with IDC plugs fitted one end (50cm length)
Longer cables can be made to order.

£19

IDC Cable Set

Doepfer MIDI Controller Kits

Doepfer MTC64

Doepfer Wheel Electronics


The Wheel Electronics allows up to 4 continuous controllers to be connected such as pitch and mod wheels, or a 4 axis joystick etc.

The Wheel Electronics is not supplied with a power supply.

An optional PSU is available


£45

Doepfer Wheel Electronics

Accessories

Doepfer Wheel Electronics

Joystick II


A Fatar joystick using two 10K linear pots, both sprung loaded to centre, the movement is 40 degrees,

so a full voltage swing is not  achieved on the output.

Joystick II is not directly compatible with any of the Doepfer pcb's, so please check the useage of this joystick
Now discontinued - only available whilst stock lasts

£25

Joystick 2 #accessories

£95